Register Now


Lost Password

Lost your password? Please enter your email address. You will receive a link and will create a new password via email.

How do you enter interface configuration mode Cisco?

Rate this Question and Answer
Asked By: Annita Duque | Last Updated: 6th May, 2020
To enter interface configuration mode, enter the interface configuration command. Interface configuration From global configuration mode, specify an interface by entering the interface command followed by an interface identification. To exit to privileged EXEC mode, enter the end command, or press Ctrl-Z.

Keeping this in consideration, how do I enter global configuration mode?

To configure a Cisco network device you must enter the Global Configuration operating mode. After passing thru the User EXEC and Privilege EXEC modes you enter the Global Configuration mode by entering the configure command. This prompt is identified by the (config), which is in the prompt.

Also, what is line configuration mode? Line configuration mode commands allow you to configure the virtual terminal line settings. To configure the virtual terminal line settings and access line configuration mode, use the line vty command in configuration mode. The CLI prompt changes to (configline).

Thereof, what is a configuration interface?

Network interface configuration. Configuring network interfaces involves assigning IP addresses, setting network parameters and hardware-dependent values, specifying network interfaces, and viewing your storage system’s network configuration.

How do I enter VLAN config mode?

Configuration Steps: 1) Issue the “configure terminal” command in order to enter the global configuration mode. 2) Create vlan using “vlan <number>” command and can assign name to vlan for description. 2) Issue the “interface [type] mod/port>” command in order to enter the interface configuration mode.

What is global configuration?

Global Configuration Management (GCM) is an application that assembles configurations for itself and other contributing applications so teams can gain an overall view of the physical and logical parts of their product offering. A global configuration represents a physical or logical piece of a product offering.

What is the difference between user mode and privileged mode?

Privileged mode mode allows users to view the system configuration, restart the system, and enter router configuration mode. Privileged mode also allows all the commands that are available in user mode. From the user mode, a user can change to Privileged mode, by running the “enable” command.

How do I configure a switch?

How to configure Cisco switches – A step by step guide
  1. 1 Before We Begin: Know What Hardware You’re Using and Download PuTTY.
  2. 2 Connect the Switch to PuTTY.
  3. 3 Enter Privileged EXEC Mode and Set a Hostname for the Switch.
  4. 4 Assign a Password to the Switch.
  5. 5 Configure Telnet and Console Access Passwords.
  6. 6 Configure IP Addresses With Telnet Access.

What is privileged mode?

privileged mode – Computer Definition

An operational state of software that has the highest priority. Also called the “supervisor mode” or “supervisor state,” it is typically the mode in which the operating system runs, because it has access to all the resources in the computer. See privilege.

What command do you enter to start privileged mode?

To get into Privileged Mode we enter the “Enable” command from User Exec Mode. If set, the router will prompt you for a password. Once in Privileged Mode, you will notice the prompt changes from “>” to a “#” to indicate that we are now in Privileged Mode.

What does the show run command show on your router?

The show running-config command shows the router, switch, or firewall’s current configuration. The running-configuration is the config that is in the router’s memory. You change this config when you make changes to the router.

What is the enable command?

Use ENABLE COMMAND or CMD to permit CP to process requests for the specified CP command. You can also permit processing of CP commands during initialization using the ENABLE COMMAND or CMD configuration file statements.

What is ROMmon mode in router?

For those of you that are not familiar with the term ROMmon (ROM monitor) mode, it is a bootstrap program that initializes the hardware and boots the Cisco IOS software when you power on or reload a router or switch.

What is Cisco CLI?

Most Cisco devices (including routers and switches) use a CLI (Command Line Interface) to configure the network device. The CLI is an interface, based on text. You type in configuration commands and use show commands to get the output from the router or switch.

How do I configure a Cisco router?

Step-by-Step Configuration of Cisco Routers
  1. Step1: Configure Access Passwords.
  2. Step2: Configure a Router Hostname.
  3. Step3: Configure IP addresses for Router Interfaces.
  4. Step4: Configure Routing (Static or Dynamic)
  5. Step5: Save your configuration.
  6. Step 6 (optional): Configure NAT.
  7. Step 7 (optional): Configure DHCP.

What is a switch port?

Switch ports are Layer 2-only interfaces associated with a physical port. A switch port can be an access port, a trunk port, or a tunnel port. Switch ports are used for managing the physical interface and associated Layer 2 protocols and do not handle routing or bridging.

How do I change the interface description Cisco?

description (interface)

To add a description to an interface configuration, use the description command. To remove the description, use the no form of this command.

Can you assign an IP address to a switch port?

No, that’s not what they‘re for. The only IP address you can assign to a switchport in a Cisco switch is for the so called Switch Management Interface Cisco Networking: Switch Management Interface Configuration – dummies. Other than that, switches work with MAC addresses, because they sit on Layer 2 (Data Link Layer).

What is SVI in Cisco?

A Switched Virtual Interface (SVI) is routed interface in IOS representing the IP addressing space for particular VLAN connected to this interface. There is no physical interface for the VLAN and the SVI provides the Layer 3 processing for packets from all switch ports associated with the VLAN.

What is span port on Cisco switch?

Destination (SPAN) port: A port that monitors source ports. This is usually the point to which a network analyser is connected. Remote SPAN (RSPAN): When Source ports are not located on the same switch as the Destination port.

How do I enable a port on a switch?

To enable or disable one or more ports using the Insight app:
  1. Launch the Insight app.
  2. If the managed devices do not display, in the menu at the bottom, tap Devices.
  3. Select the switch that you want to configure.
  4. Scroll down and tap CONFIG PORTS.
  5. Tap OK.
  6. Select the ports that you want to configure.

What is cr in Cisco configuration?

The <cr> symbol (“cr” stands for carriage return) appears in the list to indicate that one of your options is to press the Return or Enter key to execute the command, without adding any additional keywords. ( same as thon’s reply, exctract from

  • 12
  • 39
  • 39
  • 39
  • 24
  • 21
  • 9
  • 37
  • 35
  • 39