Register Now

Login

Lost Password

Lost your password? Please enter your email address. You will receive a link and will create a new password via email.

How high should a kick plate be?

Rate this Question and Answer
Asked By: Silvestra Dhurvasula | Last Updated: 27th May, 2020
Standard kick plates are either 6 or 8 inches tall. If your door has fewer than 8 1/2 inches between the bottom and the decoration, select a 6-inch kick plate.





Likewise, people ask, what side of the door does the kick plate go on?

By definition, kick plates are attached to the push-side of a door. Kick plates come in a variety of heights from 10″ tall to 16″ tall and are usually manufactured in 2″ increments.

Beside above, do I need a kick plate? A kick plate keeps all that from happening. And though it’s called a “kickplate, doors need protection from other things that go bump in the night — and day — such as strollers, animals and toys. Kick plates aren’t limited to front doors. Any door that swings into a room can benefit.

Similarly, you may ask, how do you install a kick plate?

Hold the kick plate in position and insert screws into the top and bottom holes at the center of the plate. Tighten the screws securely. Install the remainder of the screws, working out toward either edge of the plate. This procedure helps prevent warping of the plate so that it will install flat against the door.

What is a kick plate?

Kick plates are an addition to the bottom of your door that help reduce the amount of damage and stress that your door takes over time. They’re installed on the push side of the door. The term kick plate comes from the fact that when people’s hands are occupied they often kick the bottom of the door to open it.

What is the bottom plate of a door called?

Typically there are two, one on each side of the door, or there can be one on either side of the door. Sill: The bottom or piece of a door. Also known as the threshold and usually come in aluminium or wood. Stiles: The outer pieces or edges of a door.

What is the metal plate at the bottom of a door for?

Metal base plates, sometimes called kick plates, protect the bottom of the door from damage. These plates are located on the push side of the door, which is prone to scuffs. You can also use these plates to cover up minor damage on the door.

Why is a kick plate so important?

The main function of a kick plate is to protect the material of your door from taking damage off feet. The purpose is that if your hands are full, you will most likely open your door by kicking it in, hence the name kick plate.

What is the metal plate on a door called?

A strick plate is the metal piece attached to the door jamb. As the door closes, the latch mechanism strikes the plate mounted to the jamb and the strike plate catches the mechanism and holds the door closed.

How are kick plates measured?

Measure the height from the bottom of the door to the bottom of the first decorative panel or inset on the door. Subtract 1 inch from the total to allow 1/2 inch of clearance on the top and bottom of the kick plate. Standard kick plates are either 6 or 8 inches tall.

How do you cut a door kick plate?

  1. Place the door plate on a flat surface, such as a table or sawhorse.
  2. Measure and mark where the kick plate will need to be cut.
  3. Slide the kick plate so that when you are cutting it with the saw, the blade of the saw will not cut the surface under the kick plate.

How do you remove a kick plate?

Removing the toe kick from base cabinets is a relatively simple matter of prying the boards away from the cabinet. Some toe kicks have a decorative piece of quarter-round trim on the bottom that hides the bottom edge of the board. Use a simple claw hammer and a pry bar to remove the toe kick.

What is the standard toe kick height and depth?

Standard Dimensions for Toe Kicks

Toe-kick depths greater than 3 inches do not hurt the effectiveness of the toe kick, but depths less than 3 inches should usually be avoided, as they interfere with ergonomic effectiveness. The optimal height for a toe kick is 3 1/2 inches, and heights up to 4 inches are common.

How do you install a kick plate on kitchen cabinets?

Nail the toe kick board to the base cabinets with finishing nails. Position a nail setter on the head of each finishing nail. Strike the nail setter with the hammer to countersink each finishing nail. Fill each countersunk hole with wood putty that matches the color of your cabinet finish.

How do you clean a brass kick plate?

Mix several tablespoons of salt into a 1-pint spray bottle filled with white vinegar. Replace the lid and shake or stir to dissolve the salt. Spray the salty vinegar over the brass and allow it to sit for 10 minutes or so. Wipe away with a damp sponge, then towel dry the brass.

Can you put a kick plate on a fiberglass door?

Composite/fiberglass doors all have a wood frame around the perimeter. It stabilizes the cover materials and adds strength for things like door locks, hinges, and even kick plates.

Do I need a door sill pan?

Most residential builders understand that window rough openings need sill pan flashing — either a site-built sill pan made with peel-and-stick tape, or a commercial sill pan made from metal or plastic. Not only that: sill pan flashing under exterior doors is code-required.

What is a kick plate on a dishwasher?

The kickplate grille is a decorative panel that covers up the opening at the bottom of your dishwasher. If your kickplate is damaged or missing, this is the part that will replace it.

  • 12
  • 39
  • 39
  • 39
  • 24
  • 33
  • 39
  • 35
  • 33
  • 39