Register Now

Login

Lost Password

Lost your password? Please enter your email address. You will receive a link and will create a new password via email.

What does HF mean on Kenmore Elite washer?

Rate this Question and Answer
Asked By: Martinho Dole | Last Updated: 9th January, 2020
The FH error code on your Kenmore Elite washing machine is an indicator that there is a problem with incoming water. When there is little water coming into the machine, the FH code will appear and the washer will stop.


Click to see full answer



Keeping this in consideration, what does FH error code mean?

The FH error code indicates that the washer control does not detect water entering the machine within 30 seconds after the fill valves have been opened. It is also displayed after 8 minutes if the flow sensor has detected 10.5 gallons passing through it without the water level pressure switch tripping.

Subsequently, question is, what does HF mean on Whirlpool washer? water inlet valve

Correspondingly, how do I reset my Kenmore Elite washer?

How to Reset a Kenmore Elite HE Washer

  1. Press the “Stop” button twice, and then press the “Power” button.
  2. Choose a wash cycle (e.g. “Normal”), and then choose your wash options (e.g. “Hot/Cold” or “Cold/Cold”).
  3. Press the “Start” button to complete the reset process and restart the washing machine.

How do I clear the error code on my Kenmore washer?

You will need to remove the power supply to the washer to reset the code.

  1. Look for the “Pause/Cancel” button on the washer control panel.
  2. Press the “Pause/Cancel” button twice to cancel the wash cycle.
  3. Check for kinks in the water supply hose while the washer does not have power.

How do I fix error code f21 on Kenmore?

This may be an indication of a drain pump problem and/or clog in the drain line. Unplug your machine for 1/2 hour to see if the CCU will reset. If that is without result check the drain hose for kinks or if it is clogged. After that check the electrical connections to the pump and ensure the pump is running.

What does e2 mean on a Kenmore washer?

The E2 error message indicates the control has detected a shorted thermistor. Most likely replacing the thermistor will fix this problem.

What does the code 5d mean on a Kenmore washer?

The 5d code is actually an Sd code and it means suds have been detected in the washer. This can indicate to much soap or the wrong kind of soap was used in the washer. Be sure HE detergent is being used. If can also indicate the drain pump is restricted or the drain hose is kinked.

How do you unlock a Kenmore washing machine?

How to Manually Unlock a Kenmore Front Load Washing Machine
  1. Touch “Control Lock” for five seconds until “CL” disappears from the washer’s display to unlock the control panel.
  2. Press “Start/Pause” to manually pause the cleaning cycle.
  3. Pull the door’s handle to open the door and add or remove the clothing from the washer.

Is there a reset button on a Kenmore washer?

In reference to your Kenmore washer: Most washer’s can be reset like a personal computer. Unplug or turn the circuit breaker off for 30 seconds. Plug the power cord into the wall outlet or turn the breaker back on and wait 30 seconds.

How do I run diagnostics on my Kenmore Elite washer?

1 Answer
  1. With the washer empty, close the door.
  2. Push “control/on” or “Start”
  3. Select “Drain/Spin”
  4. Select “No Spin” by pressing SPIN SPEED touchpad.
  5. Push “PREWASH” option four times within 5 seconds. (If there is no PREWASH option, press RINSE HOLD 4 times in 5 seconds.)
  6. C:00 should light up and begin the diagnostic.

How do I troubleshoot my Kenmore washer?

  1. Washer will not stop when the lid is open. Bad lid switch.
  2. Water will not drain out of the washer. Clogged waste hose. Bad drain pump. Bad pump motor.
  3. Washer does not spin/agitate. Broken drive belt. Bad tub motor.

Is there a reset button on a washer?

Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.

How do you drain a Kenmore Elite washer?

How to Manually Drain Water From a Kenmore Washing Machine
  1. Pull the washer away from the wall until you have enough room to access the back panel of the machine.
  2. Place the bucket behind the washer next to the drain hose.
  3. Unhook the drain hose from the drainpipe.

Why is my Kenmore washer not spinning?

If the washer won’t spin or agitate, check the drive belt. If the belt is broken or if it isn’t tight on the pulleys the washer won’t spin or agitate properly. If the washer won’t spin the lid switch assembly might be defective. If the washer won’t spin or agitate the stator assembly might be burned out.

How do I reset my washing machine?

To perform the Master Reset, carefully unplug the washing machine from the power outlet and leave it unplugged for one minute. After one minute is up, plug the washer cord back into the wall. Next, open and close the door of the washing machine 6 times within 12 seconds to send a “reset” signal to all the components.

Why does my Kenmore washer keep beeping?

You say the washer works but the beeping is constant so the first thing I suggest you try is to put the washer into a control lock and see if the beeping continues. If you try this and the beeping stops then there is likely a stuck button. If the beeping doesn’t stop then you most likely have a control board problem.

How do I reset my Whirlpool front load washer?

Unplug the washer for 30 seconds to attempt to reset the Duet washer control. You can manually unlock the washer by removing the top (remove screws on the back of the top panel and slide the top panel back to lift off.

How do you unlock a Whirlpool front load washer?

Hold down the “Control Lock” button on your Whirlpool washer for three seconds at the end of the washing cycle. Listen, and when you hear the unlatching sound, the door should open.

How do I clear the error code on my Whirlpool washer?

To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.