Register Now

Login

Lost Password

Lost your password? Please enter your email address. You will receive a link and will create a new password via email.

What kind of wood do you use for fascia boards?

Rate this Question and Answer
Asked By: Lupicinio Huelga | Last Updated: 8th March, 2020
Wood Fascia Boards

Wood is the most common material used to make fascia. Typically, wood fascia boards are made of spruce, pine or fir. However, cedar fascia boards (same wood for decks) are gaining steam.





Hereof, what is the best wood to use for fascia board?

Cedar is a popular fascia wood and redwood is another. That’s because both species resist rot and moisture very well, even when unpainted. If you prime and paint the fascia, you can also make them out of fir, spruce or pine, which are all less expensive. You construct fascia boards out of 1-inch lumber.

Beside above, can you use treated lumber for fascia? Purchase pressure-treated lumber to replace your fascia boards as a way to extend the life of the repair. Pressure-treated lumber is designed for outside applications and resists rot, moisture and insect damage. Cut the new lumber to size and secure it to the rafter ends with galvanized finish nails.

In this regard, how thick should fascia boards be?

Replacement fascias do vary in thickness by manufacturer, but the rule of thumb is that to qualify structurally as a replacement board they should be somewhere between 16mm and 25mm thick – our most common range is the 18mm Replacement Fascia.

What type of wood is used for eaves?

cedar

What is the best material for fascia boards?

Wood Fascia Boards

Wood is the most common material used to make fascia. Typically, wood fascia boards are made of spruce, pine or fir. However, cedar fascia boards (same wood for decks) are gaining steam.

How do you seal fascia boards?

Start at the end of a fascia board and caulk the corner edge where two boards meet. Smooth the caulk bead with your finger and begin caulking the joint between the fascia board and the soffit (also known as the eave). Slowly move down the joint to apply a steady bead of caulk into the gap.

Are fascia boards necessary?

Fascia is meant to protect the roof and the interior of the home from moisture by blocking it from entry. It does have an aesthetic role as well; it creates an even appearance along the roof’s edge. If water gets behind the fascia board, it is vulnerable to damage.

How much does it cost to replace rotted fascia?

Replacing your soffit generally costs about $20 to $30 a linear foot installed, while replacing your fascia costs about $15 to $25 a linear foot installed. Prices for the project depend on a number of factors, including the materials used and the size of your house.

What kind of wood should I use for exterior trim?

A common trim board is pressure-treated southern yellow pine. It is inexpensive and widely available, but it tends to warp when it absorbs moisture. Unlike cedar and redwood, southern yellow pine is less stable and wood-eating insects consider it delicious food.

Can I use pressure treated wood for exterior trim?

Pressuretreated wood may not be the best choice for exterior trim, since most pressuretreated wood is southern yellow pine, a species that is not particularly good at holding paint. Although some lumberyards do sell premium grades of pressuretreated wood for exterior trim, this grade may be difficult to find.

How do you fix fascia boards?

Fascia roof repair tips
  1. Choose the best wood. Handpick each wood fascia board and make sure it’s from a species of wood that’s naturally decay resistant.
  2. Watch where you nail your fascia. If at all possible, never nail a fascia board near the edge of the end grain.
  3. Use the best nails.
  4. Paint the ends of your fascia boards.

How do I know my fascia size?

Multiply the 1-1/2 inch width of the fascia board by the slope of the roof (e.g. 4/12). 1.5” times 4 divided by 12 = 0.5 or ½ inch. For a 2×6 fascia board at a 4/12 slope, the trim size would be 1-1/2 inch x 5 inches for an overhang without a soffit.

What is the board behind the fascia called?

The fascia board is the one mounted at the point where the roof meets the outer walls of the house and is often called the ROOFLINE. However most people refer to it by the name of the main board that carries the gutter – the fascia or fascias.

How do you cut angles for fascia?

Set the angle of a miter saw to 45 degrees so you can make clean cuts through the board. Put on your safety glasses, and position the fascia board so the corner on one end lines up with the saw blade. Turn the saw on and pull it down to cut the angle. Cut the ends of any other boards that will be on a corner.

Can you use Hardie board for fascia?

HardieTrim boards provide unmatched durability and allow you to create a variety of design possibilities for trim, gables, corners, fascia, windows, doors, column wraps, rakes, friezes, decorative trim and other non-structural architectural elements.

How do you replace fascia with drip edge?

Removing Drip Edge Eave Strips:
  1. Gently lift up the shingles along the lower edge of the roof, and find the nails attaching the eave strip to the roof decking.
  2. Use a flat pry bar and hammer to remove the nails holding the eave strip to the roof decking.
  3. Slip the eave strip out from under the shingles.

What is fascia board made of?

The fascia is a board that runs along the roofline and acts as a finishing edge or trim that connects to the ends of the rafters and trusses. Fascias are visible from the exterior of the home and typically hold gutters in place. Most fascia boards are wooden, but they can also be made from vinyl, aluminum and plastic.

How do you prepare fascia boards for painting?

A: First you need to scrape and sand down the old fascia boards. Caulk all the joints and nail holes in the old and new boards with paintable caulk. Then apply a special wood primer to both old and new wood. Once that primer soaks in and hardens, then you can paint all wood with a 100 percent acrylic flat paint.

How soon can you paint treated wood?

“There are differing opinions on how long pressure-treated wood should sit before painting — some say a year, others six months. It depends on how dry the wood was when it was installed. “One test is to sprinkle some water on it — if the water is absorbed, it’s ready to be painted.

What material is used for eaves?

Roof overhangs, also known as eaves, can be finished in a number of materials—including PVC, wood, or aluminum.

Can I use plywood for soffit?

plywood are often used for soffits, optimum appearance and finish performance is achieved by using panels with Medium Density Overlay (MDO), or textured (such as APA 303 Siding) or sanded A-grade faces. Top-quality acrylic latex house paint systems perform best and are the only systems recommended for A-grade faces.

  • 12
  • 39
  • 39
  • 39
  • 24
  • 35
  • 30
  • 25
  • 31
  • 22